Knot of the Week: Adapting the Diamond Hitch for a Truck Bed Tie Down

Diamond Hitch for a Truck Bed Tie Down

In our previous two knots in our Knot of the Week series, we showed you how to tie a Diamond Hitch and Artilleryman’s Loop. Today we’re going to show you how to combine these two knots for use as a tie down in a truck bed.

There were some comments in our Diamond Hitch article asking for a method to be able to use it with only four lashing points rather than the six our article required. Utilizing the Artilleryman’s Loop and some extra paracord, we’ll show you how to make this happen!

Diamond Hitch » Hitches

(Strength: 3/Secure: 4/Stability: 4/Difficulty: 3)

Please refer to our Knot of the Week introduction post for a description of what these ratings mean.

Diamond Hitch for a Truck Bed Tie Down

The first thing you’ll need to do to utilize a Diamond Hitch as a tie down in a truck bed, is to create the two missing mid-point lashing loops required to make it work. This can be done one of two ways.

One way is to take a line all the way through each of the four existing tie down points, making a box. After creating the box, tie in one mid-point Artilleryman’s Loop on the bight within each of the long sides.

Another option would be to simply have two sections of paracord, or other rope, strung between each long side of the truck bed tie downs with an Artilleryman’s Loop at the mid-point. It’s important to note that while we used paracord in the video and photos, stronger and thicker rope might need to be used depending on the load that’s being tied down.

Uses:

  • Securing a load
  • Tie down for a roof rack, truck bed or pack animal

Tying Instructions:

  1. Once you create your additional midpoints using the Artilleryman’s loop, attach the standing end of your line to one of the fixed midpoints.
  2. Use the working end to span across the load and to the opposite midpoint.
  3. Route the working end through the second midpoint and back to the original midpoint.
  4. Wrap or pass the working end through this original midpoint.
  5. Grasp the double line created over your load and twist the two lines six times or so, creating a diamond pattern in the center.
  6. Ensuring to keep the diamond pattern, run your working end to the closest corner of your tie-down points.
  7. Wrap or pass the working end through this corner point and through the backside of the center diamond before passing it down to the opposite corner.
  8. Wrap or pass the working end through the opposite corner and down through the top of the center diamond and out to the bottom-most corner.
  9. Wrap or pass the working end through this corner point and back through the backside of the center diamond before passing it to the last corner.
  10. At this point take a few seconds to adjust the lines and tighten them up.
  11. Pull tension at the last corner and secure the working end to the midpoint you started at, which completes the Diamond Hitch.
  12. Optionally we’ve used the Taut-Line Hitch to secure the working end so if the load shifts you can adjust the tension.

Video and Photos

Posted in Hitches | Tagged , , , , , , , , | 1 Comment

Negligent Discharges and a Learning Experience to Take Home

Negligent Discharge SERPA MainThere’s a YouTube video that’s currently circulating around the Internet that shows YouTuber Derek Grebner, of Tex Grebner Outdoors, taking his audience through his Negligent Discharge and how he wound up shooting himself in the leg with his Kimber 1911.

His expensive bullet wound could have inflicted much more damage and he was extremely lucky he didn’t blow out his entire knee cap. I strongly feel that this ND could have been prevented by better trigger discipline, but I’m sure he probably thinks that himself too.

While I agree with Derek’s statement that he didn’t feel it was caused by the Blackhawk SERPA holster, I still feel like the SERPA is NOT A BEGINNER’S HOLSTER. The SERPA holster relies on your index finger to slightly depress or graze the trigger guard release to draw your firearm. If trigger discipline is not fully developed or rushed, it’s easy for an index finger to curl and press the release, rather than slightly rub the release with a properly indexed trigger finger.

If the index finger is already curled while drawing, hopefully you can imagine how easy it would be for that finger to naturally find the trigger. I personally own and have used a SERPA multiple times and have my own reasons for disliking it, but this issue isn’t one of them. I feel an important take home message from viewing this video is that

In the video he states that his thumb safety was disengaged on his draw stroke, due to another holster he was previously using, but that information is irrelevant. This could have happened to anyone using a Glock or Sig which doesn’t utilize a thumb safety at all.

I commend Derek for coming forward with this video and showing his mistake as a learning experience, hopefully everyone reading this article will take note of this and learn from it. He certainly handled the incident well considering he’d just shot himself on video. It’s also an important reminder of why we advocate having a trauma kit like our ETA Kits readily available!

Posted in Firearms, News | Tagged , , , | 48 Comments

Celebrate Independence Day with Good Old Fashioned American Patriotism

The 4th of July is all about commemorating the adoption of the Declaration of Independence which gave America its independence from Great Britain, right?

“But why do Americans celebrate so much and blow things up?” a comment I recently read on a forum I frequent. I thought I’d answer this question and throw up a great quote by John Adams, one of the signers of the Declaration of Independence.

The second day of July, 1776, will be the most memorable epoch in the history of America. I am apt to believe that it will be celebrated by succeeding generations as the great anniversary festival. It ought to be commemorated as the day of deliverance, by solemn acts of devotion to God Almighty. It ought to be solemnized with pomp and parade, with shows, games, sports, guns, bells, bonfires, and illuminations, from one end of this continent to the other, from this time forward forever more.

While Adams was off by two days, this quote pretty much sums up what every American should be doing to celebrate our independence! While it might seem most days that our government has veered from the founding ideals our forefathers envisioned back in 1776, I know I’ll never forget what the Declaration of Independence means and be celebrating just as Adams wanted!

How have you celebrating American Independence this 4th of July weekend?

Posted in Memorial | Tagged , , | 4 Comments

Dogs of War: Tactical Uses of Scent Detection

4 of 6 in the series Dogs of War

We don’t have the technology, we can’t build him better…

In my previous articles on dog capabilities, and how to integrate them into a Tactical Team, we discussed their capabilities to bite and fight as well as their ability to carry equipment. Now let’s discuss their most beneficial capability to us, their sense of smell.

In my original article I said, “One of the greatest capabilities a dog can bring, and the primary reason they are used by law enforcement and military, is their sense of smell. Humans walk into a restaurant and smell the food (they may even distinguish the types of meals being prepared).

A dog detects whether it’s an electric, gas or wood stove being used; the type of meat being cooked; the spices being added; the cleanliness of the cooks; the sicknesses of the patrons; who is carrying weapons; and if there are any explosives of drugs present on the grounds. Wouldn’t you love to be able to tell all that with just your sense of smell?”

This is not exaggeration and could even be expanded to, they can tell you which cars in the lot have gas or oil leaks, which rooms in a hotel have bed bug problems, where the fire that burned down your neighbor’s house started and what accelerant was used to start it, where the dead body of that victim is in that pond, where cancer is in a patient, and even where a woman is in her cycle. And all of this simply through their sense of smell.

Philosophy of Scent

Opinions are like belly buttons, everyone has one. That’s kind of what it’s like with people and their theories. Everyone has a theory about something and many people have theories about everything. But theories are only useful when they are tested in practical application.

For instance, it is common consensus and seems to make total sense that your scent will blow down wind; so that if it is a windy day, the dog will tend to track on the downwind side of your actual trail. However, during a tracking course at Baden K-9 several years ago, we were demonstrating scent discrimination on an open field.

It was a breezy day with fairly constant winds blowing and every dog that day tracked up wind of where the tracks were. They all found what they were tracking, but the point is that dogs have access to a world that’s invisible to us. Theory is great, but when we ignore or neglect practical application and stop trusting the dog to reveal to us this invisible world, we will fail in our mission.

We could make all sorts of additional theories as to why the scent was upwind that day and I am not saying that scent flows upwind, I am just saying that we simply don’t understand everything there is to know about that world. But this doesn’t mean that we can’t use the incredible senses of the dog to reveal it to us. We just have to trust that the dog has abilities that we can’t even come close to matching. When you understand and embrace this, you’ll be able to begin making real progress toward mastering tracking and scent work.

Tactical Uses for Scent Detection

Practically everything has a scent to it. You may not be able to detect scent on some things, but that doesn’t mean that your dog can’t. The key to making a dog’s sense of smell useful to the tactical operator is to communicate to the dog what scents you want him to indicate on and how.

For instance, you may want a dog to sit when he detects explosive scent. You may want him to point or lay down when he detects humans on the other side of a door or hidden in the wood line. You can train these indications however you want, but keep in mind that you have to maintain these skill sets. It is also useful to be able to turn the dog on and off, in a manner of speaking, such that you do not always require them to be in full detection mode.

Detecting Explosives

For the Tactical Team, one of the greatest threats to their safety is an explosive booby trap. These can be produced in many ways, but all of them have one thing in common…explosives. Training a dog to indicate on explosives allows the team to move faster onto the objective, confident that they will not trip a wire or activate a pressure switch. Dogs can be trained off lead to follow verbal commands or hand and arm signals for which route to take.

Upon the detection of any explosive material, the dog will indicate. This gives the team the capability to reroute to avoid the device, or disarm it. Either way, this process is many times faster than the careful “observe and feel” method, and much more reliable. Dogs can also be trained to indicate on these scents while tracking so that you don’t come unexpectedly upon a booby trap either intended to kill you or indicate that you are actually tracking.

When raiding a fairly large compound with a fairly small team, you don’t have the time or resources to search everything and leave appropriate security on every location searched. This is another area where the dog can be of great assistance to the team. Using various marking devices (the red or green laser pointer being the most popular) you can train a dog to check rooms and other locations for the presence of people.

This is where it is critical to train a different indication for people and explosives. If a dog checks a room and sits, DO NOT kick the door down (assuming sit is your indication for explosives), but if a dog indicates by pointing, then you know someone is in there. The only question is, are they hostile or hostages.

Multiple Dogs

I have not mentioned this much, but this is a time when having multiple dogs with multiple teams can be particularly useful. Depending on the mission parameters and tactical considerations, you can work three (3) or more dogs on a 12-man team. The Nazi SS K-9 Teams had up to 3 dogs per handler with the highest number I am aware of being 12 dogs with a single handler.

I am not suggesting that every member of a SEAL raid team should have three dogs, but if you are planning for dog integration, don’t get stuck only considering a single dog.

Another application for human detection is cave searching. Dogs were used extensively in cave searches in Afghanistan. With their sense of smell they can detect things like the cave walls and small openings in caves in the complete blackness without the need to use light to see. They will also never get lost in a cave because they can back track their way out.

Tracking

Finally, dogs can be used for both hostile and non-hostile tracking situations. While there are schools that specialize in teaching men to track, the methods, while effective, are extremely slow and unless the person stops moving, your chances of locating them are slim. They simply move faster than you can track them in many instances. But a dog can track as fast as you can move. In fact, the handler is usually slowing the dog down from moving too quickly. Consider that dogs track their prey in the wild, and in case you have never noticed it, deer mosey much faster that we can move comfortably through the bush.

Tactical Teams may find they need to conduct a non-hostile track in the event of a lost teammate or downed pilot. In an isolation event, the isolated person has specific procedures that they take to indicate that they are close, but can still move up to a kilometer away from their last indication. With a dog on a rescue team, once this initial location is found, the dog can lead to the missing person in a matter of a few minutes.

Much more important in terms of team safety, however, is the hostile track with a dog. In this event the team may walk into an ambush or come unexpectedly upon the enemy they are searching for. Dogs will naturally indicate when they are getting close on hot scent. After training with a tracking dog, the handler should be able to determine when they are danger close and the team can determine to release the dog off lead or move into the objective in a way that best suits their environment and threat level.

The dog’s ability to man-track is a significant tactical advantage to the team needing to locate a fleeing suspect in the shortest time possible. Even if the time window is not critically short, the dog allows for the focus of the Team members to be on the threat, and not on the ground.

Dogs Communicate with Humans

No, you do not need to be a dog whisperer to understand a dog’s communication. You simply need to understand that all animals communicate in subtle ways. Birds do not announce to the flock that they are about to make a left turn and begin descending, and yet you do not see mid air collisions within a flock of birds when they dip and dive in flight. In a similar fashion, dogs will communicate with humans.

Some of this communication can be trained, such as sitting when the dog smells explosives. Other indications are natural, such as indicating on sound and the way a dog reacts when they suddenly catch hot scent just before coming on the tracked subject. It is the responsibility of the handler to know their dog.

They must know how their dog responds in different environments and situations; what their dog’s indication is before biting when they were previously calm; what their dog’s indication is when they are on and off scent during a track; or even how they act when they are nervous or tired. Understanding your dog and his individual personality is critical in taking full advantage of the dog’s senses and communication to the Team.

Join us next time as we discuss in more detail, the combat capabilities of a dog in the use of their sense of hearing.

Joel is the founder and head trainer of Dunetos K-9, a training facility and equipment manufacturer specializing in Tactical and standard K-9 equipment. He has been training and handling dogs for over 10 years and works closely with Baden K-9, a highly respected training facility in Ontario, Canada. Joel has served in the United States Army for 11 years as a Military Police Officer deploying to the Pentagon days after the 9/11 attack, Afghanistan (2003), Iraq (2007) and is currently serving in Bogota, Colombia (2011) in the War on Drugs. Joel has specialized in integrating dogs into every aspect of life, from personal obedience and protection to specialized military application.

Image courtesty of ABCNews.com

Posted in K9 | Tagged , , , , , | 2 Comments

DIY AR-15 Build: Safety Selector and Pistol Grip Installation

6 of 8 in the series DIY AR-15 Build

Today in part six of our DIY AR-15 Build you’ll learn how to install an Ambidextrous Safety Selector and Pistol Grip in your Lower Receiver.

Ambi Safeties are definitely a personal preference and not for everyone. We’re of the opinion that if having to transition to an off-handed shooting position, the ambi safety is a definite benefit.

The Pistol Grip we’re using is the Magpul MOE Pistol Grip that’s been coated in Desert Digital by our friends at CRC Hydrographics. They’ve also introduced a brand new rubberized clear coating we’ll be talking about as well.

Continue reading for our step-by-step instructions for installing the Safety Selector and Pistol Grip with detailed photos and video.

Safety Selector and Pistol Grip Installation

The Stag Arms Ambi Safety Selector is a quality selector that will add some versatility to your safety manipulation, especially if having to transition to your off hand. The downside is being accustomed to having the ambi selector and then in the situation where you’re not shooting your own firearm. This goes with any accessory though on the AR platform.

DIY AR-15 Build - Safety Selector and Pistol Grip Installation

Something to note on the Safety Selector spring is that it looks very similar to the two takedown pin springs included in a lower parts kit. The easy way to tell the difference is to play the “one of these things is not like the other” game, but the Safety Selector Spring is stiffer than the other two and definitely looks different.

One reason we’ve used the Magpul MOE Pistol Grip for this build is due to its versatility of being able to house a spare bolt and firing pin in the storage core. This is also great if you have more than one AR and they each have Magpul Pistol Grips capable of holding the core, as you can have a single spare firing pin and bolt and switch the core to the gun you’re running.

CRC Hydrographics

DIY AR-15 Build - Safety Selector and Pistol Grip Installation

We were interested in getting all our Magpul accessories coated while assembling this build, as we’ve had an interest in the durability of water transfer imaging and how it holds up compared to Krylon. We reached out to CRC Hydrographics and are very fortunate we chose them for our needs, as they’ve just released an additional service they call “Grip-Tec.”

Grip-Tec ads an additional flat protective coating on top of the water transfer, which is nicely rubberized! It’s hard to show photos or video of the Grip-Tec at work, but from what we can say about our feedback so far is awesome! It really seems like a fantastic addition to their dipped patterns. Some intial feedback they’ve gotten so far is that it works well both combined with gloves and without.

It’s also important to note that the Grip-Tec is for use on firearm contact points such as stocks, grips, rail covers and handguards, etc. CRC notes that it’s also been popular on bolt action rifle stocks. We’re thoroughly impressed with the quality of the water transfer imaging and are looking forward to getting this build completed and putting it to the test.

Parts Needed:

DIY AR-15 Build - Safety Selector and Pistol Grip Installation

Tools Needed:

Assembly Instructions

DIY AR-15 Build - Safety Selector and Pistol Grip Installation

  • Insert the port side of the Ambi Safety Selector into the Lower Receiver, pointing to the safe position.
  • Insert the Lower Receiver Upside down onto the Vise Block so you’re staring at the threaded hole where the pistol grip will secure to. (Make sure your hammer is set in the rear position)
  • Affix the opposite side of the Ambi Safety Selector and using the included hex wrench, tighten the screw. Witness marks help too.
  • Drop the Safety Selector Detent into the small hole just port of the Pistol Grip Screw hole.
  • Take the Pistol Grip, In this case we’re using a Magpul MOE Pistol Grip, and insert the Safety Selector Spring into the hole on the top of the Pistol Grip (pointed side down).
  • Hold the spring with your finger as you work the Pistol Grip into proper position.
  • Once in place screw in the Grip Screw into the bottom of the Pistol Grip.
  • Perform a function check at this point by placing the Safety Selector in the safe position and cock the hammer back. Leave your thumb on it so that it doesn’t accidentally get thrown forward, as this can damage your lower in some cases.
  • Squeeze the trigger, ensuring that the hammer doesn’t release and the safety is doing it’s job.
  • Keep your thumb on the hammer and rotate the Safety Selector to “fire.” When you now squeeze the trigger you should feel the hammer release. Guide it forward while keeping the trigger depressed.
  • Move the hammer to the rear and hear it engage the disconnector. Release the trigger now while keeping your thumb on the Hammer. You’ll see the hammer move forward slightly while it disengages from the disconnector and engages the trigger sear.

Join us back here soon for our 7th installment in the DIY AR-15 Build where we’ll be assembling the Trigger Guard!

Posted in Firearms | Tagged , , , , , , , , | 6 Comments

Cultural Support Teams AKA Female Special Operations in Combat

Hopefully the men of Afghanistan are holding on tightly to their head scarves, because American women are joining forces with their male counterparts in combat.

According to today’s post on Military.com the U.S. Army Special Operations Command has begun deploying female soldiers as part of front-line commando units. These soldiers will assist Special Forces and Ranger units by leading Cultural Support Teams (CST) which will interact with the female segments of Afghan society providing not only intelligence support but also social outreach. Approximately 30 female soldiers are already in the field.

This is good news for women who’ve wanted to serve in combat positions and have been waiting for positions to emerge. I’m excited for new service opportunities for interested and qualified female soldiers, but I’m also concerned that this new step into combat is in a part of the world that is so harmful and unforgiving towards women. I guess there is no graceful and cushy entrance into combat.

What are your thoughts on women in combat?

Posted in News | Tagged , , | 41 Comments

Why You Should Learn How to Pick Handcuffs to Escape from Illegal Restraint

Why You Should Learn to Pick Handcuffs

Yesterday, a Baltimore couple was handcuffed by Police impersonators during a home invasion, where the man was subsequently shot in the neck!

One of the skill-sets we advocate here at ITS Tactical is picking locks as well as handcuffs to prepare yourself for any situation, including this recent Baltimore scenario. While Police are unsure of the motive in the Home Invasion/robbery, there’s no denying that being able to escape this kind of illegal restraint is beneficial to know!

Here’s our article on How to Pick Your Way Out of Handcuffs, as well as some related articles linked below. Stay safe and learn the skill-sets that could one day save your life!

Posted in Lock Picking | Tagged , , , | 7 Comments

Magnum Boots Launches new Blog and Awesome Giveaway!

Magnum Boots, longtime ITS Tactical supporter and all around good people, have officially launched their own in-house blog and are celebrating in a big way.

Their blog, titled BLDG4801, provides insight on what’s happening at Magnum, in-depth interviews with key industry insiders, sneak peaks at new Magnum products, contests & giveaways and reviews from field testers, bloggers and editorial writers.

Do yourself a favor and head over and enter their awesome contest where they’re giving away $1,000 in Magnum gear to one lucky guy or girl! To enter simply head over to this page for all the details on how to enter!

 

Posted in News | Tagged , , | 2 Comments

Remembering Operation Red Wings and those Lost on June 28th 2005

I distinctly remember the news circulating around the Naval Special Warfare Center on June 28th, 2005, that four SDV SEALs were missing following a SR (Special Reconnaissance) mission in North Eastern Afghanistan.

Later that day I also learned of a downed MH-47 Chinook carrying a QRF (Quick Reaction Force) of 8 SEALs and 8 Night Stalkers attempting a rescue mission. It was a bone chilling realization that I had just heard about the greatest loss of life the community had seen since WWII.

It briefly flashed me back to the events of September 11th, as I had many of the same feelings of wanting to do something, but being unable to. All I could do is stand by for further news of the tragedy.

Everyone in the office I was stationed at huddled around the computers and telephones eagerly awaiting news of the four missing SEALs. By the end of the day that Tuesday, we still had no confirmation that any of the four SEALs had survived. Continue reading

Posted in Memorial | Tagged , , , , , , | 16 Comments

Announcing the ITS Tactical Discreet Messenger Bag Gen 2!

We’re excited to announce the release of the 2nd Generation ITS Tactical Discreet Messenger Bag! We’ve listened to suggestions from our end users and worked hard with Zulu Nylon Gear to integrate some awesome new features!

The Discreet Messenger Bag represents features unseen in other bombproof tactical messenger bags; A bag laden with tactical features that doesn’t look tactical! With no exposed MOLLE/PALS or visible velcro, this bag is sure to blend right into any urban environment as your everyday carry or bug out / bail out bag.

Today we’ll go through all the upgrades we’ve made to increase its versatility and inherent discreet nature! Continue reading

Posted in ITS Information | Tagged , , , , , , , , , , , , | 20 Comments